SOURCE: https://forum.huawei.com/carrier/en/thread-82497.html
What I LIKE in Huawei after few weeks using it
-open SFP
that mean you can use any sfp brand, it will not complain, but I don’t know that will void warranty
in Aruba you can use 3rd party sfp but that will void warranty
in Ruckus open SFP as well but won’t void warranty
-1 year warranty
like Cisco
unlike Aruba and Ruckus which is limited lifetime warranty (the best in warranty, you can have 100 years warranty)
-price could be cheaper than anything else
that’s why most countries using it nowadays
-almost all the switches are L3 switch
if you want more feature such as vxlan, just add license
-telco in mind
you can have AC or DC power module in the back. if you want to change AC to DC, just add DC module
if you want more poe power just add two AC power modules
it has anti static port in the back
NEED TO IMPROVE
-save need in User mode
unlike Cisco that you type “do wr me” in config mode
unlike Aruba that you just type “wr me” in any mode
-who answer in forum is not technical enough compare to Cisco and Aruba forum
| Cisco | Huawei |
| [no equivalent: shows the files used for startup] | display startup (user mode) |
| ? | ? |
| aaa | aaa |
| boot | boot bootrom |
| clear access-list counters | reset acl counter all (user mode) |
| clear counters | reset (user mode) |
| clear crypto | ipsec sa |
| ike sa | |
| clear interface | reset counters interface |
| clear ip bgp | reset bgp all |
| clear ip cef | reset ip fast-forwarding |
| clear ip route * | reset ip routing-table statistics protocol all |
| clock | clock |
| conf t | system-view |
| copy running-config | save filename |
| debug / no debug | debugging / undo debugging |
| debug pvc nego | debug atm all (very dangerous – might crash router) |
| disable | super 0 (number is privilege level from 0 to 3, where 3 is default and equivalent to “enable” on Cisco) |
| enable | super |
| enable secret (conf mode) | super pass cipher (system mode) |
| end | return or ctrl+z |
| exit | quit |
| ip tacacs | hwtacacs nas-ip (this command doesn’t exist !!!) |
| mtu | mtu |
| no | undo |
| ping | ping |
| reload | reboot |
| router bgp | bgp |
| router rip | rip |
| send | send (user mode) |
| show | display |
| show atm pvc | display atm pvc-info |
| show clock | display clock |
| show controller | display controller (but not relevant for non-modular chassis) |
| show crypto isakmp key | display ike peer |
| show crypto isakmp police | display ike proposal |
| show crypto isakmp sa | display ike sa |
| show dsl int atm 0 | display dsl status interface atm 2/0 |
| show flash | dir flash: (user mode) |
| show frame-relay pvc | display fr pvc-info |
| show interfaces | display interface |
| show ip bgp | display bgp routing-table |
| show ip interface | display ip interface |
| show ip nat translation | display nat session |
| show ip route | display routing-table |
| show logging | display logbuffer |
| show policy-map interface | display qos policy interface |
| show port | display port-mapping |
| show snmp | display snmp-agent statistics |
| show startup | display saved-configuration |
| show tech | display diagnostic-information |
| show users | display users |
| show version | display version |
| shutdown | shutdown |
| snmp-server | tftp-server (system mode) |
| tacacs-server | hwtacacs scheme (system mode) |
| telnet | telnet |
| terminal length | screen-length disable |
| undo screen-length disable | |
| terminal monitor | terminal debugging (user mode) |
| terminal no monitor | undo terminal debugging (user mode) |
| traceroute | tracert |
| write erase | reset saved-configuration |
| write mem (or wr or copy run start) | save |
| write terminal (sh run) | display current-configuration |
Nbctcp's Weblog 